Oil Change On The Off Road Truck

14 Pri 2021
111 930 Shikime

www.letsdig18.com/ for shirts and more
Save 10% off your first Ariat order - ariat.dkkdet.net/c/2697242/696794/10644
Chris' Favorites -
ariat.dkkdet.net/c/2697242/1010848/10644

Komente
  • Always good to have a strong magnet in your shop.

    The PickleThe Pickle4 ditë më parë
  • Take the lid off the filler tube

    James BreaultJames Breault14 ditë më parë
  • My lathe uses a similar filter to the 7791. In fact I’ll probably use it the next time I have to change it since the 7791 is a 16 micron.

    Tim BeneTim Bene20 ditë më parë
  • The drain plug you removed is connected to a tap on the engine oil pan (sump) by a hose. I expect this tap is not fully open and this is why the oil flow is so slow at the drain plug on the belly guard.

    Ian BarnesIan Barnes24 ditë më parë
  • I used to drive an A20 at a landfill back in the late 90's early 00's... Shocks in the seat were shot, and someone had used a bunch of rubber tie straps from the seat back to the handle on the escape hatch to hold it up. Get going a little too fast in the thing and you were in for a /wild/ ride. And I still remember the first time I ever tried to back the thing up. Yeah, I was a pretty good ways more than 45° off where I wanted to go. And the guy that was showing me how to run it was cracking up big time. XD Even had the pleasure of taking it about 10 miles down the highway once. Let me tell you, 30mph in one of those things even on smooth pavement is /no/ joke. Would not recommend. What sucked, was I was gone for a couple years in the middle... When I'd left everything worked, there was a little bit of slop as expected for it's age, but was overall in pretty darn good shape. When I came back, the place had been under new management for a while and apparently nobody ever kept up with maintenance, and it was wallered out /hard/. No brakes, lost a couple gallons of oil a day, lights busted off, glass cracked, super extra sloppy everything to the point I'm sure it'd never been greased once, cab full of mud, electrical system fubar, etc... Volvo tech never could get the main brakes past the point of dumping half the air in one brake press to barely slow it down a bit, so I screwed around enough with it to get the parking brake on the driveshaft working again, which was a trip to try to feather to slow down, and had a snap-in handle that tended to pop out at the /worst/ times. The other equipment had fared about the same or worse, and some were just so dangerous to operate that we'd use anything else possible before resorting to them only if absolutely necessary. The less said about the scraper's quarter mile or so high speed trip down the side of the hill, across a ~20'x6' ditch, and across the neighboring field, the better. I'm so glad I noped out of there when I did.

    hwessonhwesson24 ditë më parë
  • You need to go magnet fishing to get your pipe back.

    Jerry JohnsonJerry Johnson24 ditë më parë
  • The 2.5 gal jugs work really nice as well. They aren't so heavy but can carry a bunch more per load. 😎😎

    ckhallock88ckhallock8825 ditë më parë
  • OMGOODNESS......your pup is super cute!

    Dan SchneiderDan Schneider25 ditë më parë
  • Finally a ALworldr who buys Walmart brake cleaner haha. $1.94 a can here in Las Vegas. Beats $4-5 at parts stores. Coolant oil etc so much cheaper.

    Derek TippitDerek Tippit25 ditë më parë
  • few years ago you use do tapes on maintain and care to equipment maybe add to show young guys how bid and get state and fed certification to getting bid bonds ,..lot guys on here But none go that far , sure little green apples after that 10 million view ,your going more likely get call from Discover Channel ..But..watch them

    target Estimating Servicestarget Estimating Services27 ditë më parë
  • not really look my Mercedes e-class 6 Cy take 8.2 QT

    target Estimating Servicestarget Estimating Services27 ditë më parë
  • Dogs can count up to 3 -4...so he would be expecting at least 3 nuggets....just saying.

    CHARLES MAIRCHARLES MAIR27 ditë më parë
  • The bottle was dusty but the liquor was clean😀

    Robert CookRobert Cook28 ditë më parë
  • hey Chris just wondering if you ever lived in florida. orlando area just seems we have met.

    mike o'neilmike o'neil28 ditë më parë
  • ➡️ cams.downloadz.to ⤵️ B.e.S.T f'u"l'l D.a.T.i.n.G h.o.T G.i.r.L's -L-o-V-e-S-e-X---❤️😘 ..👍 !💖🖤❤️今後は気をライブ配信の再編ありがとうです!この日のライブ配信は、かならりやばかったですね!1万人を超える人が見ていたもん(笑)やっぱり人参最高!まさかのカメラ切り忘れでやら1かしたのもドキドキでした,. 💖🖤在整個人類歷史上,強者,富人和具有狡猾特質的人捕食部落,氏族,城鎮,城市和鄉村中的弱者,無`'守和貧窮成員。然而,人類的生存意願迫使那些被拒絕,被剝奪或摧毀的基本需求的人們找到了一種生活方式,並繼續將其DNA融入不斷發展的人類社會。. 說到食物,不要以為那些被拒絕的人只吃垃圾。相反,他們學會了在被忽視的肉類和蔬菜中尋找營養。他們學會了清潔,切塊,調味和慢燉慢燉的野菜和肉類,在食品市場上被忽略的部分家用蔬菜和肉類,並且學會了使用芳香的木煙(如山核桃,山核桃和豆科灌木 來調味g食物煮的時候 1618858128

    radoo radooradoo radoo28 ditë më parë
  • Remember, Rotella is good in engines and Nutella is good on toast. Not the other way around though.

    Jim's videosJim's videos29 ditë më parë
  • I had a feeling when you Sid you were going to put 7 gallons in there before even checking it That it was going t be Full when you checked it, Sure glad our didn’t put 3 more in it 😱🥴

    Anna FraleyAnna Fraley29 ditë më parë
  • do you get an oversized permit every time you have to haul your equipment to locations or is there a permanent permit for what you do

    bwill07bwill0729 ditë më parë
  • Its not cheap to transport filters i guess. In europe Volvo oe filters cost at best less than 20 bucks a piece :D

    Th3R4kTh3R4k29 ditë më parë
  • Buy a big magnet, and go fishing.............

    John ParkerJohn Parker29 ditë më parë
  • A doggo! Trying to steal all viewers from Andrew Camarata :D

    yks sieluyks sielu29 ditë më parë
  • Napa filters are made by Wix, which is a phenomenal brand. I bet Volvo filters are made by Wix as well

    alan newhallalan newhallMuaj më parë
  • Such a handsome boy...... Winston, I knew what you were thinking!

    cat637dcat637dMuaj më parë
  • Fill tube is probably magnetic. Do you have a family on that farm? Never have seen an introduction video on you! Might help your algorithm!.

    trebornesregrottrebornesregrotMuaj më parë
  • Lol We have a few A60's at work...they are very nice to drive but but compared to the ridged chassis trucks are very high maintenance, fragile and unforgiving of rough operators.......also pretty much the smallest trucks on the mine.

    Coal fired paradiseCoal fired paradiseMuaj më parë
  • Gotta be something obstructing the drain hole from the factory.

    MrErichonda30MrErichonda30Muaj më parë
  • You need to partner with ALworld personality louis rossman to help protect the right to repair. Things that we take for granted like rights of owning equipment is getting attacked by corporate lawyers.

    Delanez DelanezDelanez DelanezMuaj më parë
  • do you take the oil fill cap off to let air in to stop the oil air locking when draining

    Amanda GirlAmanda GirlMuaj më parë
  • Egp

    Tommy PateTommy PateMuaj më parë
  • 👍🇺🇸🇺🇸🇺🇸🗽🙏🏻 Enjoyed!

    Larry Iowa/Texas RoosterLarry Iowa/Texas RoosterMuaj më parë
  • I’ve never been so happy to see someone use Elecitrical tape

    Kristopher JadwinKristopher JadwinMuaj më parë
  • The company I was working for tried using napa filters on there cat 330d , I went to start it one cool fall morning and as I was walking away I looked back and oil was pouring out the compartment where the filters were. Come to find out the holes where smaller than the cat filters and couldn't take the pressure of the cold oil and blew the o-rings out of the top of the filters, no more napa filters for the chitty only cat

    Ryan DelaneyRyan DelaneyMuaj më parë
  • IF YOU PLAY WITH BIG MACHINES TO MAKE BIG MONEY IT COST BIG MONEY!!!!!!!

    steve1966steve1966Muaj më parë
  • Did you pull the dip stick to allow air in?

    NY CatNY CatMuaj më parë
  • Excellent video.

    Frank Ramos Jr.Frank Ramos Jr.Muaj më parë
  • is it meant to be 3yrs between services?

    Jeff MooseJeff MooseMuaj më parë
  • I think i'm a little ... stupid. A guy put near 10 gallons of oil in a massive truck and make a vidéo, and me i watch that, and i'am happy ?! where is my problem ... don't answer, it's not needful. :-) I subcribe to this channel few yaers ago, but i am reassured, we are at the moment 83 439 people who watched it. Thank you for the vidéo.

    Stéphane LamarreStéphane LamarreMuaj më parë
  • Hot oil and filling cap off usually does the trick, or even pour some diesel in the engine and turn it over a little to make the oil thinner. That also has the benefit of clean out old gunk.

    Erik OhrlingErik OhrlingMuaj më parë
  • he does it right...

    jim poteetjim poteetMuaj më parë
  • Get yourself a fishing magnet and pull it up.

    Rick BronsonRick BronsonMuaj më parë
  • There is no way u put a gallon in each filter.

    Jason HerdJason HerdMuaj më parë
  • lol shit you but in 7 gal, faster then i can get 1.5 gal into my bike ... :p

    Jeff AndrewsJeff AndrewsMuaj më parë
  • use a magnet on a string to pick up the tube in the tank bro

    Graywolf gamingGraywolf gamingMuaj më parë
  • Hot glue it..

    Willy WongWilly WongMuaj më parë
  • open the oil fill might go faster

    ShadowSalC1ShadowSalC1Muaj më parë
  • Good to see ol Mr Donnie he’s a hoot

    Elite Earthworks LLCElite Earthworks LLCMuaj më parë
  • magnet on a string will probably get the suction tube back.

    Brian FullertonBrian FullertonMuaj më parë
  • Would the oil drain quicker if you took off the fill cap?

    I dig the earth in PAI dig the earth in PAMuaj më parë
  • Not sure if you know this, but if you use el cheapo black PVC tape on something, you can make it impervious to most everything by whapping the tape over itself one or two times and then coat the tape thoroughly with PVC glue. The glue will melt the tape and make everything waterproof...Of course yocan spend the big bucks for 3M nasty glue, but about everyone has the cheapo tape around with the glue.

    ted coffmanted coffmanMuaj më parë
  • thank you

    Mark HayhurstMark HayhurstMuaj më parë
  • Sounds like one of my days LOL

    Terry ClementTerry ClementMuaj më parë
  • I've been wrenching on things-mechanical, building engines and fixing things for over 50 years. If that engine were mine, I'd have to know why the oil drains so slowly. Is there a screen around the pump pick-up, and the drain plug is within the screen? That would be one explanation. Air-cooled VWs were like this.

    Dave PDave PMuaj më parë
  • I forgot to put the drain plug in my 71 Maverick, one time. It ran out on the garage floor. I would think about writing oil on 1 or 2 5 gal gas cans with a breather plug on it. like writing the date and hours on the filters.

    Jay StringerJay StringerMuaj më parë
  • Crack your oil filter to release pressure/ vacuum on oil system for faster draining. Also, cut the bottom 6" off a drum and weld two rebar handles on sides for high capacity catch pan. 1 for oil and use top part of barrel with bung plug installed for antifreeze drain pan

    Er IcEr IcMuaj më parë
  • Ya should remove oil fill cap and or filter to allow air to get behind the oil to allow it to flow better but ya great vid and Godbless and stay safe

    brian meatteybrian meatteyMuaj më parë
  • Great videos homeboy. Try opening up the fill valve and release valves? Add air and it flows

    Lawrence CervantesLawrence CervantesMuaj më parë
  • I just LOVE the fact that the front grill folds down into an access ladder for the engine bay... Someone on the Engineering Development team was using both Brains AND Common Sense... They probably got fired as soon as Upper Manglement realized it...

    A WilsonA WilsonMuaj më parë
  • If it's a steel pipe that fell into the oil tank, you could always go magnet fishing for it...

    A WilsonA WilsonMuaj më parë
  • magnet on a piece of cord & go magnet fishing for the dip tube

    Bill ForrestBill ForrestMuaj më parë
  • I've missed the farm/house videos

    Tim CTim CMuaj më parë
  • good video

    ramtuff2007ramtuff2007Muaj më parë
  • Are other dogs jealous? I find Gorilla tape to be the best stuff well as far as tape of course not for electrical

    Jake SchislerJake SchislerMuaj më parë
  • Very interesting video, enjoyed it. Thanks for sharing..

    Andy SukosdAndy SukosdMuaj më parë
  • unscrew an oil filter

    watchthe1369watchthe1369Muaj më parë
  • Build a stand for the tank to sit on, let gravity be your friend.

    Roger WeaverRoger WeaverMuaj më parë
  • so what your saying is if you put tape on your shaft it makes it a tigher more snug fit ?

    Joe LongJoe LongMuaj më parë
  • i remember a fitter, who worked on tractors, told me that he told the apprentice to fill a ford tractor with oil, the apprentice said no problem, a couple of hours later the fitter asked the apprentice if he was finished, they worked in a large workshop, he replied " she's full" the guy went to start the tractor but it spluttered and refused to start, it turned out that the apprentice had literally filled the engine it it was coming out of the rocker cover filler lid he'd put about 20 gallons of oil in the engine 😂

    david mcculloughdavid mcculloughMuaj më parë
  • 14:20 cute 🥰

    FEELING HEALING FREQUENCESFEELING HEALING FREQUENCESMuaj më parë
  • Am I the only one that likes the maintenance videos just a little more

    No NameNo NameMuaj më parë
  • Is that a south thing? U never put filters on with a wrench

    logging05logging05Muaj më parë
  • open the filler cap or breather ? that is way too slow to drain.

    Spring HollowSpring HollowMuaj më parë
  • Looks like you had a Mcgyver day, is that a different A30D?

    j rehtilj rehtilMuaj më parë
  • I wonder if that oil will dissolve the PVC pipe?

    Craig SmithCraig SmithMuaj më parë
  • Oil drains slow on my caterpillar 305 to is swear they do this for labor time for your mechanic for the owner operator that’s owns it I swear it’s the most boring maintained on the machines

    Jon HarringtonJon HarringtonMuaj më parë
  • Take the top filling cap off just like the other guy said to .prob air lock.

    Derek BrakeDerek BrakeMuaj më parë
  • So magnet fishing in oil isn't on the menu.

    Ken SmithKen SmithMuaj më parë
  • Dang, Ima have to get some of those tater tots and see if they are as good to me as they are to Winston!

    95thousandroses95thousandrosesMuaj më parë
  • time to give the truck a good attention ,,

    Idr 82Idr 82Muaj më parë
  • In 2024 you can do it again. WOW

    JohnnyputtJohnnyputtMuaj më parë
  • That's where a big strong magnet on a rope comes in handy

    FactFinderFactFinderMuaj më parë
  • Now you really do remind me of my dad with that toothpick in your mouth...👍👍🇺🇸

    Frances StrattonFrances StrattonMuaj më parë
  • A magnet on a string might recover the lost section of tube???

    QuantityEngineersQuantityEngineersMuaj më parë
  • Looks in great order for the hours. Great video mate

    jon lowejon loweMuaj më parë
  • What was the ambient temperature? Was the engine hot at the point of draining? Was the filler cap off/released? Just pulling the dipstick might not be enough to prevent a vacuum from forming, at the top of the system.

    furriephillipsfurriephillipsMuaj më parë
  • Magnet fishing in the oil tank!! 🤣🤣.

    Buckin Right420Buckin Right420Muaj më parë
  • At least that metal pipe won't rust whenever you recover it

    Simon HarwoodSimon HarwoodMuaj më parë
  • Next time open the fill cap and it will gush out

    Syed Hassaan Mujtaba BokhariSyed Hassaan Mujtaba BokhariMuaj më parë
  • Interestingly my motorcycle takes the same oil.

    Will JosephsonWill JosephsonMuaj më parë
  • Doesn’t Cat have oil analysis available for customers? Usually well worthwhile for the detailed oil analysis.

    Ordinary MiraclesOrdinary MiraclesMuaj më parë
  • I would have slotted the pvc pipe and dropped it to the bottom and then attach the pump.

    sn99cobrasn99cobraMuaj më parë
  • What oil weight? Could you magnetic fish for the AWOL pump tube?

    Alan L. SimmonsAlan L. SimmonsMuaj më parë
  • I must have missed the part where Chris asked for advice on getting tube out or getting oil to drain faster?!?!?

    Wayne TharpWayne TharpMuaj më parë
  • There is a special hose with a fitting to push the safety open and the oil will drain.

    Jeremy CoxJeremy CoxMuaj më parë
  • I prefill my filters also, but I like your idea of sitting the filters in the boxes while filling. Love your video's.

    Kevin JensenKevin JensenMuaj më parë
  • is todd adams the driver that is picking it up?

    Hank AdamsHank AdamsMuaj më parë
  • Hi Chris What happened to a magnet on a bit of string? Great Video Regards to all Richard 🇬🇧

    Richard ChiversRichard ChiversMuaj më parë
  • 600 dollars for three oil filters and two diesel fuel filters that’s robbery Volvo are modern day robbers

    David GillettDavid GillettMuaj më parë
  • Set that oil tank up on blocks where you can get the jugs under a spigot instead of using that hand crank pump!

    Kip CuddKip CuddMuaj më parë
  • Farmers were the creators, and first inventors of do-dads-n-thing-a-ma-bobs.👍

    Globalist JuiceGlobalist JuiceMuaj më parë
  • It is probably vacuum locked, try pulling the dipstick next time.

    Martin SpamerMartin SpamerMuaj më parë
ALworld